Can Factory Brake Controller of 2007 GMC Sierra 2500HD be Bypassed without Dash Codes

Question

Question:

I have a 2007 GMC Sierra 2500HD new body style. I pull a 28 foot fifth wheel camper. I would like a new brake controller and the factory controller. Once I install the new controller, how do I get the brake control message off my dash? What controller would you recommend? Thanks for your time.

asked by: Nick O

0

Expert Reply:

If you bypass the factory brake controller in your 2007 GMC Sierra 2500HD properly you would not have any error codes appear on the dash display. You also would not have to have the computer of the truck reprogrammed in any way which means you don't have to make a special trip to a dealer.

To see exactly how to do this check out the help article I linked on this page. It will walk you through the entire process. It's basically a few wiring connections that need to be made under the dash of the truck and under the hood.

For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies a proportionate amount to the trailer brakes.

expert reply by: Jameson C

0

Answer 1

We can help you with this. When installing an aftermarket brake control into your 2018 Chevrolet Silverado 2500 that is equipped with a factory Integrated Trailer Brake Control (ITBC), you will have to disable the ITBC first before the aftermarket…

view full answer...

Answer 2

There isn't anything like an autonomous controller that would step up if the factory controller fails. I'd simply bypass the existing factory brake controller. The GM ITBC, although it works better now than the earlier models has been…

view full answer...

Answer 3

Installing the P3 brake controller #90195 on your 2015 Chevy Silverado 2500 with factory integrated controller will actually be very simple. What you will do is use harness #3016 which plugs into a port on the truck already. But you will need to…

view full answer...

Answer 4

In order to replace the factory brake controller on a 2016 Chevrolet Silverado 2500 you'd need to cut the blue brake output wire from the harness where it would normally plug into the vehicle side brake controller plug and run this to the rear…

view full answer...

Answer 5

Check out the FAQ article I attached that details exactly what you will need to do to bypass your factory controller in your 2014 Chevy Silverado with the P3 #90195. It's pretty easy to do actually. The link is down below the product links. The…

view full answer...

Answer 6

Yes, there is another option to add a brake controller to your Silverado. Since you have the factory tow package, I recommend the Curt Echo In-Line Wireless Brake Controller item #C79DR. The controller plugs in behind your 7-way with included…

view full answer...

Answer 7

You will first need to make sure that the new tail lights are wired the same as the old ones. There are basically 2 types of wiring systems. First there is a 2-wire system that has combined turn signals and brake lights on the same circuit/bulb. And…

view full answer...

Answer 8

The best option we have for locking a fifth wheel hitch like the part #C16044 to the bed of your truck is a cable lock like part #e98891. You would want to route the cable through the head of the hitch and through a stake pocket hole in the bed of…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...