How To Remove Spindles From Trailer Axle

Question

Question:

how do you remove the spindle i ground all the welds on the back side

asked by: MICHAEL L

0

Expert Reply:

Trailer spindles are welded directly to the axle so to remove one it just needs to be cut off completely using a torch or saw.

Then to replace the spindle such as with the EZ Lube # TRU37FR that you were looking at it's extremely important that it be done by a certified welder who is experienced with this type of job. It has to be welded perfectly square to the axle or you're going to have constant problems with the trailer's suspension once everything else is put into place.

Because of the cost of having a certified welder perform this type of job in many cases it is actually cheaper to just have the entire axle replaced with one that includes the needed spindles. I have attached a link that will take you to our complete axle selection if you decide to go this route.

expert reply by: Chris R

0

Answer 1

You can convert a single axle trailer to a tandem axle but it's more extensive than just putting the extra axle on there. The current axle does need to be repositioned for proper tongue weight. You will also need to cut off the current…

view full answer...

Answer 2

To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel…

view full answer...

Answer 3

To get the best braking power for your boat trailer you would want to have disc brakes on both axles. If you happen to be limited to one axle then you would want the rear outfitted. With a 5,000lb boat you likely have two 3,500lb torsion axles. The…

view full answer...

Answer 4

Looks like you are in need of a number 42 spindle like the part #TRU37FR. The numbers you listed aren't part numbers but judging by the shape of what you sent in a picture of this is a match. You still might verify this though by measuring…

view full answer...

Answer 5

The spindles can be replaced. However, they will need to be welded by a certified welder. They use special jigs so that it is concentric and square on the axle or it can cause problems with uneven tire wear and wheel tracking. I've linked…

view full answer...

Answer 6

The axle placement formula listed below will need to be calculated using the trailer's gross vehicle weight rating (GVWR). The gross vehicle weight rating (GVWR) is the most the trailer can weigh loaded. This will ensure that the trailer is…

view full answer...

Answer 7

I spoke with my contact at Dexter regarding the axle on your trailer. He stated that the serial number you found is a pretty old number and unfortunately they don't have much information on this particular axle. He was not able to confirm…

view full answer...

Answer 8

For 7,000 lb Dexter hub assemblies, you could have 1/2 inch or 9/16 inch, or 5/8 inch drive in studs. I've linked the page of our drive in wheel studs for you. Once you have the right stud based on your measurements you can get the correct…

view full answer...

Answer 9

To determine the axle size you will need there are some measurements needed. First, if you are replacing the axle then you can measure the one you have. Measure from the center of one spring seat to the center of the other spring seat. Then measure…

view full answer...

Answer 10

If you have a round 3" diameter axle on your Spartan boat trailer then you are going to want to use the CE Smith U-Bolt Kit part #CE23003 which contains u-bolts that are 7" long x 3-1/8" wide x 3/8" diameter. The reason you need…

view full answer...

Answer 11

I have another option for you, but the CE Smith U-Bolt Kit #CE23003 you were looking at is designed for 1-3/4" springs and will not fit with your 2" wide springs. Instead you will need two of the U-Bolt plate #TRTP300200 per axle, and two…

view full answer...

Answer 12

The best leaf spring option we have is the part #e28SR which has a 5,000 lb axle capacity and is 25-1/4 inches in length. Old springs do tend to stretch a bit over time but in your case this capacity matches what you are in need of and is a close…

view full answer...

How To Remove Spindles From Trailer Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching