Which Curt Gooseneck Hitch Fits 2013 Ram 2500 Mega Cab

Question

Question:

Will this product fit on my 2013 ram SLT mega cab 4x4 with hemi ?

asked by: Jorge A

0

Expert Reply:

Yes, the Curt Double Lock, Flip and Store Underbed Gooseneck Hitch w/ Installation Kit # C607-661 that you referenced does fit your 2013 Ram 2500 Mega Cab short bed. We confirmed this with Curt. I attached an install video for this kit for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The B and W Turnoverball Gooseneck hitch part #BWGNRK1313 that you referenced is the correct fit for your 2010 Dodge Ram 3500 short bed with the megacab. I attached an install video for this for you to check out as well. Good looking pup by the way!

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The Gen-Y Hitch 5th Wheel to Gooseneck Pin Box part #GY58GR is primarily designed for long bed trucks. It's no different than a standard fifth wheel pin box in regards to the size. If you were using a fixed hitch and standard pin box before with…

view full answer...

Answer 10

If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for a…

view full answer...

Answer 11

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Answer 12

Hey Ted, so if you look in the bed of your truck and see 5 holes/pucks that would mean you have the OEM prep. I'd assume if you had it you'd have seen them by now. If you had it you'd only need a ball like the part #C60618. If you…

view full answer...