Is Trimming Rear Fascia of 2014 Subaru WRX Hatchback Required

Question

Question:

Is it necessary to cut the fascia on a 2014 wrx hatchback? Or can it be left intact?

asked by: Geoffrey N

0

Expert Reply:

Yes, rear fascia trimming is required to install the EcoHitch part # 306-X7261 on your 2014 Subaru WRX Hatchback. The rear fascia has to be cut so that the shank of the hitch will fit. I attached a picture that shows where you'd need to trim the rear fascia.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For your 2014 Subaru Impreza WRX 5 Door Hatchback WRX with the Invidia single exhaust. I recommend the EcoHitch Stealth Trailer Hitch Receiver - Custom Fit - 2" Item #306-X7261. This hitch hugs the spare tire pan and mounts to the frame…

view full answer...

Answer 2

The EcoHitch Stealth Trailer Hitch Receiver #306-X7261 you are referring to can be removed from your 2009 Subaru Impreza in the same way it was installed, which is to remove the bolts which can be done with a torque wrench, though keep in mind you…

view full answer...

Answer 3

The vehicle body harness you need to plug into is located under the left (driver's side) sidewall. If you can't get easy access to it, I recommend removing the panel to gain easy access and then reinstalling the panel once connected.…

view full answer...

Answer 4

The EcoHitch Stealth Trailer Hitch Receiver - Custom Fit - 2" #306-X7261 you asked from for your 2012 Subaru Impreza is not compatible with your 400 lb motorcycle with a carrier. This hitch is only rated for a max capacity of 300 lbs. That…

view full answer...

Answer 5

I reached out to EcoHitch to see if they had any fitment notes on your 2012 Subaru Impreza WRX with the Invidia R400 Gemini Exhaust. They were not able to confirm or deny that their Stealth Trailer Hitch Receiver #306-X7261 will fit with that…

view full answer...

Answer 6

The stealthiest hitch we offer that fits your 2015 Audi Q5 is the Draw Tite part #75940 which only has the hitch opening hanging below the rear fascia. See attached picture to see what it looks like installed. We do not have any options that are…

view full answer...

Answer 7

All hitch makers base their designs on a vehicle's stock exhaust setup. There are just too many aftermarket items to allow them to do testing to confirm hitch compatibility with a car that has one of these. Draw-Tite hitch #DT24959 and Curt…

view full answer...

Answer 8

As long as your 2011 Subaru WRX hatchback isn't a STI model we have the EcoHitch part #306-X7261 that fits with the quad exhaust which is a hidden hitch with a 2 inch opening or we have the Curt part #C11120 which is a 1-1/4 inch hitch.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Is Trimming Rear Fascia of 2014 Subaru WRX Hatchback Required

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching