How to Adapt B and W Companion Fifth Wheel Hitch to Fit 2019 Ford F-350 Rail Kit

Question

Question:

Will the head off my bwrvb3500 fit on this base? Have the base and head for the Bandw rvb 3500. Purchased a new 2019 Ford F-350 super duty. Just want the new base

asked by: Mike W

0

Expert Reply:

Yes, the head of your current B and W hitch part # BWRVK3500 will fit on the base part # BWRVB3305 to give you a hitch that's compatible with your 2019 Ford F-350 with the factory rail kit. One thing you might consider is that it would be easier to resell your current hitch as a complete hitch if you instead went with the hitch part # BWRVK3305 for your Ford rail kit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Thank you for the photo of your Lippert pin box. You have their model 1116. I confirmed this with my contact at Lippert. The Trailair Air Ride 5th Wheel Pin Box #LC155943 that you referenced is a direct bolt-on replacement for the 1116. It comes…

view full answer...

Answer 2

In general the aftermarket pin boxes do achieve a better clearance than the stock pin boxes simply because they offer more adjustability. The Trailair Flex Air 5th Wheel Pin Box #LC328492 will give you an additional 3-3/4 inches in length and the…

view full answer...

Answer 3

You wouldn't need to remove any air from a Trailair like the part #LC155943 while storing it. Just be sure to check to make sure the pressure is correct when you go to tow again. The air system of this pin box is very heavy duty and lowering the…

view full answer...

Answer 4

If you have a Curt Q20 fifth wheel hitch, part #C16530, we have just what you need. You can use part #C16017. This is the legs that will work with the factory rail kit on your 2017 F-250. These legs will work with Curt E16, A16, Q16, Q20, and Q24…

view full answer...

Answer 5

To convert your Curt Q20 to fit the factory rail kit of your 2017 Ford F-350 you'd want to replace the base with a fixed leg kit that fits the Ford rail kits of your truck with part #C16017. You'd attach the head center section of your Q20 to…

view full answer...

Answer 6

The leg kit you need to install the head and center section of your Curt Q20 hitch in the factory rail kit of your 2011 Ford F-350 with the factory towing package is the part #C16017. This would be all that you need.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...