Inside Height of Utility Storage Box

Question

Question:

is this tall enough to store a gallon jug of oil are windshield washer fluid, a gallon of engine coolant?

asked by: Stephen

0

Expert Reply:

I checked with the manufacturer and the inside height of the Buyers Products Utility Storage Box # 3371712230 is 11-1/2 inches and its width is 29 inches. So if your gallon jug of oil, windshield washer fluid or engine coolant is just under those dimensions it will fit!

I have added a link to a video review of this storage box for you to check out as well.

expert reply by: Kyle S

0

Answer 1

Yes, I pulled the Stromberg Carlson Trailer Cargo Tray Cargo Carrier #CC-255 and test fit it with the Buyers Products Utility Storage Box #3371712230 to find that they fit together. The base of the toolbox measures 29" long x about 14-3/4"…

view full answer...

Answer 2

The Buyers Products Utility Storage Box #3371712230 is waterproof, but it does not provide a seal of any type and would not provide an air tight seal that would allow it to be submerged in water without allowing some in. With that being said, it will…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 8

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...