Recommended Winch for Raising and Lowering Pop-Up Camper

Question

Question:

Instead of using a hand crank to raise and lower the pop up camper so that you can get it to set it up. What would you use?

asked by: Susan

0

Expert Reply:

What a lot of people use to raise and lower their pop-up camper is an electric winch. For that I highly recommend the Bulldog Winch # BDW15006 because it has a load-holding brake and can power the load both in and out for raising or lowering your pop-up.

The Bulldog # BDW15006 is also easy to use with its plug-in remote with a 20' lead.

expert reply by: Kyle S

0

Answer 1

If you're going to use a winch to raise and lower your popup you will want a winch that power loads both in and out. With a winch that will only power load in you will only be able to raise the popup and not lower with the winch. We have…

view full answer...

Answer 2

The Goshen DLB 800 Winch is a left hand winch which refers to the side of the winch the handle is on. For a replacement, I recommend the Dutton-Lainson Hand Winch part #DL74FR which is also a left hand winch with 800 lb capacity so it will be an…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack…

view full answer...

Answer 9

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…

view full answer...

Recommended Winch for Raising and Lowering Pop-Up Camper

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching