Torklift Glowstep Recommendation for Doorway Height of 36 Inches

Question

Question:

I have a truck camper which has a door threshold height of 36inch what would be the appropriate product for that situation?

asked by: Hank B

0

Expert Reply:

Since your doorway/threshold height is 36 inches the correct Torklift GlowStep is the part # TLA8004 which has a threshold height range of 32-1/2" - 44" and would work perfectly. I attached an install video for this kit as well as a picture of what it looks like installed too.

expert reply by: Jameson C

0

click to enlarge

Answer 1

What I think you are asking is if the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear, #TLA7844 has a latching connection or some type of quick disconnect feature to remove from the camper. They do not have what I would call a…

view full answer...

Answer 2

TorkLift GlowStep Camper Scissor Steps - 4 Steps - Aluminum - 20" Wide - 350 lbs Item #TLA7804 has an ideal mounting bracket height of 34-1/2 inches but could still be used at 36 inches. The problem though is that the steps may not reach…

view full answer...

Answer 3

Since the TorkLift GlowStep Camper Scissor Steps #TLA7803 and TorkLift GlowStep Camper Scissor Steps w/ Landing Gear #TLA7803-8000 you were looking at are designed to be mounted with 6 lag bolts to hold the steps to your bumper, I recommend…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

I may have different installation method for you, but there is not an extended bracket made to push the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7843 away from your camper to clear your bumper. It may be possible to have a…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...