Longer Ball Mount Recommendation with 10k Capacity

Question

Question:

Hi, can you tell if its possible to find a solid welded 10kmin ball mount? Need 4inch drop and 14min center of ball to center of pin Thank you for your help

asked by: Jason

0

Expert Reply:

The Curt ball mount part # D900 that you referenced actually fits all of your criteria. It has a 10k capacity when used with the 2-5/16 inch ball, has a solid shank for the hitch and ball platform and has a distance of 15-1/4" from the center of the pin hole to the center of the ball hole. It can also drop up to 5-3/4 inches.

expert reply by: Jameson C

0

Answer 1

I spoke with Curt Mfg. and the the shank can be flipped, but the receiver portion or head must be oriented with the bolt and welded braces on top.

view full answer...

Answer 2

For use with a weight distribution system, I recommend the Curt Weight Distribution Shank #17120. The drop needed to compensate with your truck will be different for each truck. I have attached an article on how to determine what size drop or rise is…

view full answer...

Answer 3

The distance from the hitch pin hole to where the gusset meets the shank on the Curt #D900 is 4-1/4". Whether or not this will work will depend on how far down your hitch hangs. The greatest amount of clearance from the hitch pin hole is 7"…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...