How is the Shank and Head Supposed to be Oriented on the Curt Multi-Ball D900

Question

Question:

Which side up does this D900 go into the hitch? Really it could slide in both ways, just want to make sure i dont put it in wrong. On the picture the screw end is facing up, if you flip it around the screw would be facing the bottom.

asked by: charles b

0

Expert Reply:

I spoke with Curt Mfg. and the the shank can be flipped, but the receiver portion or head must be oriented with the bolt and welded braces on top.

expert reply by: Patrick B

0

Answer 1

I just spoke with my rep at Timbren. The height of the Timbren Suspension Enhancement System - Rear Axle Item #T62FR for your 2010 Toyota Tundra is 3 9/16 inches for the rubber spring portion and 1 5/16 inches for the bracket with a combined overall…

view full answer...

Answer 2

The biggest difference between the Timbren and SumoSpring jounce-style springs is that the Timbrens tend to be a bit more stiff which is great for heavier loads but can make the unloaded ride on your 2021 Toyota Tundra a bit more harsh. The…

view full answer...

Answer 3

When using the Curt Multi-Ball Adjustable Ball Mount, #D900, you should not have any problems as long as you stay within the capacities of the ball mount, trailer hitch, and your 2010 Chevy Silverado 1500. The D900 is constructed of solid steel which…

view full answer...

Answer 4

Timbren systems are designed to absorb road shock which does increase the life of the factory suspension. You will want to first make sure that the suspension is in good working order before installing and using the Front Suspension system,…

view full answer...

Answer 5

The distance from the hitch pin hole to where the gusset meets the shank on the Curt #D900 is 4-1/4". Whether or not this will work will depend on how far down your hitch hangs. The greatest amount of clearance from the hitch pin hole is 7"…

view full answer...

Answer 6

For use with a weight distribution system, I recommend the Curt Weight Distribution Shank #17120. The drop needed to compensate with your truck will be different for each truck. I have attached an article on how to determine what size drop or rise is…

view full answer...

Answer 7

The Curt ball mount part #D900 that you referenced actually fits all of your criteria. It has a 10k capacity when used with the 2-5/16 inch ball, has a solid shank for the hitch and ball platform and has a distance of 15-1/4" from the center of…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

How is the Shank and Head Supposed to be Oriented on the Curt Multi-Ball D900

Product Page this Question was Asked From

Continue Researching