Can Demco Coupler # DM14793-52 Have Holes Drilled for Installing Coupler

Question

Question:

Can this coupler be drilled with 4 bolt holes on the top side to match the bolt pattern on our Livinlite 2014 16DBS? The bolt pattern on our Livinlite does not bolt from the side but from the top to bottom. The coupler that we are wanting to replace is a bolt on A frame RAM brand with a 5k limit.

asked by: Roger J

0

Expert Reply:

Yes, the Demco A-Frame Trailer Coupler # DM14793-52 that you referenced could have holes drilled to match what you have on your trailer. This coupler would be a great option to replace a Ram brand coupler. I attached a picture that shows how the coupler latch system works for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I reached out to Lets Go Aero for confirmation that you can even use the Demco 50-Degree A-Frame Coupler #DM15349-52 and they said that you will not have any structural issues with having the bolt holes drilled in the sides of your Frame as the…

view full answer...

Answer 2

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for…

view full answer...

Answer 3

Yes the Demco A-Frame Trailer Coupler #DM14793-97 could be welded instead of bolting it to the trailer. Instead though I would recommend the #DM14793-52 which isn't primed so would be a bit easier to weld.

view full answer...

Answer 4

The Demco A-Frame Trailer Coupler #DM14793-81 (Black) or #DM14793-52 (Silver) do not come with bolts. You will need to use 1/2" Grade 5 hex bolts with them. I've added links to video reviews of each coupler for you to check out.

view full answer...

Answer 5

I would be happy to help you find the correct rated safety chains for your 15' car trailer, but you will need to confirm the GVWR (Gross Vehicle Weight Rating) of your trailer to be sure the chain is rated properly. For example the Curt…

view full answer...

Answer 6

Depends on the weight of the trailer. If the trailer will never weigh more than 5,000 lbs then you wouldn't necessarily have to go with a 5k rated coupler like the Demco part #DM14793-52 that you referenced. 5,000 lb couplers are very…

view full answer...

Answer 7

This is a great question, and it really depends on your setup. If the safety chain loops on your tow vehicle are spaced far apart then you will need more slack to make a tight turn than if they were closer together. I recommend that you connect your…

view full answer...

Answer 8

I went out into our warehouse and grabbed a Demco A-Frame Trailer Coupler #DM14791-97 to get the dimension you are looking for and found that from bottom of the top plate to the bottom flange of the coupler measures 3-1/4 inches.

view full answer...

Answer 9

The Bulldog Collar Lok Coupler part #BD028287 matches what you listed. It's an A-frame coupler with a 7k capacity that fits a 2 inch hitch ball.

view full answer...

Answer 10

Most couplers actually don't come with safety chain loops on them. Reason being that if for some reason the coupler came attached from the trailer you'd want the chains on the trailer frame so that they'd still be effective. Welding a…

view full answer...

Answer 11

A high-capacity A-frame trailer coupler cannot have the ball coupler portion cut off and a new similar part bolted on. The result would be a reduced and unknown weight capacity; it is a sure thing that the repaired coupler would not have anything…

view full answer...

Answer 12

The inside dimension of the Demco A-Frame Trailer Coupler w/ Jack Hole, part #DM14791-97 is 2-12 inches. I have attached a photo of the underside of the coupler with the dimension noted for you.

view full answer...

Can Demco Coupler # DM14793-52 Have Holes Drilled for Installing Coupler

Product Page this Question was Asked From

Continue Researching