Replacement Fan Blade for Fan-Tastic 8100DM

Question

Question:

I need to order the fan blade for the 8100DM. Is it available?

asked by: Frank T

0

Expert Reply:

I reached out to a representative of Fan-Tastic Vents who confirmed that the correct replacement for your Fan-tastic model 8100DM is the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans # FVK8017-00.

This comes with a bow-tie bracket, motor, and fan blade; the blade is not available as a separate item. I have added a link to a video review of this part for you to check out.

expert reply by: Kyle S

0

Answer 1

For a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade replacement for the Magnetek Converter Series 6300 Model 6332 that you have now.

view full answer...

Answer 2

It sounds like you might have a Create-A-Breeze B8100 model fan, which is a Fantastic Vent series fan. The correct replacement for the fan and motor on 8000 series units is the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...