Rubber Cover for OEM Gooseneck on 2018 Chevy Silverado 2500

Question

Question:

Will this replacement cover fit a 2018 Chevy Silverado 2500 HD with the factory underbed puck hitch system?

asked by: Todd

0

Expert Reply:

I spoke to a representative of Curt who told me that the Replacement Rubber Cover for Curt Underbed Gooseneck Trailer Hitch # C66165 WILL fit the factory gooseneck hole on your 2018 Chevy Silverado 2500HD.

expert reply by: Kyle S

0

Answer 1

There is one replacement cover that we know will fit the OEM gooseneck for your 2017 GMC Sierra, though it is not from BMW, it is made by Curt. For that the correct part is the Replacement Rubber Cover for Curt Underbed Gooseneck Trailer Hitch…

view full answer...

Answer 2

Your Curt Gooseneck Hitch #C60723 should have shipped with standard gooseneck ball #C60616. The High-Rise Ball is part #C60603. I measured both hitch balls in our warehouse; their tip to tip lengths are 8-3/4-inches for standard ball #C60616 and…

view full answer...

Answer 3

The Replacement Rubber Cover for Curt Underbed Gooseneck Trailer Hitches #C66165 is 2-5/8" in diameter and will fit in gooseneck holes that take standard 2-5/16" diameter shanks.

view full answer...

Answer 4

Since the Curt Pop-In Ball for Factory Ford and Ram Underbed Gooseneck Hitches - 2-5/16" Diameter Ball #C60601 you have in your 2018 Ram has been lubricated, I recommend removing the rubber plug you mentioned at the bottom of the ball and…

view full answer...

Answer 5

The Curt Ball and Safety Chain Loop Kit for Chevy, Ford, GM, and Nissan Underbed Gooseneck Trailer Hitch #C60692 does not need to be greased unless the mechanism isn't working properly. A spray penetrating spray grease works well, don't over…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 12

According to B&W the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit part #BWGNRK1020 is about a 2 hour install by a professional. All the Hardware is provided. I have attached the installation instructions so you…

view full answer...

Rubber Cover for OEM Gooseneck on 2018 Chevy Silverado 2500

Product Page this Question was Asked From

Continue Researching