Can Generator Remain on the Stromberg Carlson Trailer Tray Cargo Carrier # CC-255 During Use

Question

Question:

So very nice and out of the way to have the generator mounted on the tongue. Im new to RV practice So forgive my question. Can I opperate the generator while on the mount. IE leaving mounted...

asked by: David G

0

Expert Reply:

Yes, you can leave your generator mounted on the Stromberg Carlson Trailer Tray Cargo Carrier # CC-255 while you are using it! I would just be sure to mount the generator in such a way that the exhaust isn't pointing towards anything while in use.

expert reply by: Jon G

0

Answer 1

If you check out the picture I attached you can see that when the Stromberg Carlson Bunk Adapter part #CC-255 is installed you still have really great access to the propane tanks of the RV.

view full answer...

Answer 2

It would probably be much easier to fill tanks with the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255 if you had a soft cover on the tanks instead of a hard cover.

view full answer...

Answer 3

The BAK Revolver X4 Hard Tonneau Cover part #BAK79131 will sit about 1-1/2" to 1-3/4" below the bed rail. According to my research, the 2019 Chevrolet Silverado 1500 has bedsides which are 22" tall which means that you will…

view full answer...

Answer 4

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers, #CC-255 has about a 29" clearance from the top of the trailer frame at its mount point to the cargo tray. A 30 lb. propane tank measures approximately 24" in…

view full answer...

Answer 5

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers part #CC-255 is not going to provide the best ground for your generator. However, we do not carry Champion Generators therefore I strongly urge you to call the manufacturer to…

view full answer...

Answer 6

The Stromberg Bunk Adapter part #CC-255 is a great solution for what you are looking for. This attaches to the frame members of your camper and gives you a platform up above the propane tanks to carry a generator. I attached a picture of this…

view full answer...

Answer 7

I have a great solution for you that will not require adding a hitch to the trailer so you won't have to move the spare tire and mount. Take a look at the Stromberg-Carlson cargo carrier #CC-255. It mounts at the front of an A-frame trailer frame…

view full answer...

Answer 8

It will be a close fit but your 18" x 25" generator will fit on the tray of the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255. If you look at the linked photo you can see that the very front of the tray measures 24-3/4" long,…

view full answer...

Answer 9

It might make it a little more involved to get to the LP tanks, but the Stromberg Carlson Trailer Tray Cargo Carrier #CC-255 would only provide a slight interference if any at all. Basically, like the pictures indicate there will be a tray several…

view full answer...

Answer 10

The Stromberg Carlson Trailer Tray Cargo Carrier for A-Frame Trailers - 300 lbs #CC-255 does have the angled front corners as you stated. The generator dimensions of 22.5 x 17.3 will have absolutely no issue with fit as the generator won't extend…

view full answer...

Answer 11

If you can't place any weight on the trailer in any way that limits a lot of the options. Basically you'd have to decide if you could fit in in the interior or use a bunk like part #CC-255 as a platform on the tongue of the trailer. This is…

view full answer...

Answer 12

As long as you secured the Tote-N-Stor securely on the Bunk Adapter part #CC-255 yes you could do what you are looking to do. There's no reason it couldn't be stored on the bunk.

view full answer...

Can Generator Remain on the Stromberg Carlson Trailer Tray Cargo Carrier # CC-255 During Use

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching