How Much Grease Do I Put in the Bearing Buddy Bearing Protectors

Question

Question:

On the initial install. Do you fill until grease comes from the edges ?

asked by: Jon

0

Expert Reply:

In regards to installing the Bearing Buddy Bearing Protectors part # BB1781, you will need to fill them with grease until the grease starts to seep out of the seal around the piston (see photo). You should see the piston extend out past the Bearing Buddy label when it's properly filled. It has an automatic pressure-relief feature so you don't need to worry about blowing out the grease seals.

I have attached a review video which talks about this process as well.

expert reply by: Conner L

0

click to enlarge

Answer 1

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 2

Ideally, you'll want some of the hardware attaching the e-track to the trailer floor to also secure to the cross members as well as to the planks that make up the trailer floor. If that's not possible, I'd recommend using a backer plate…

view full answer...

Answer 3

If you are looking for a grease cap PLUG with the TRP stamped on it chances are the Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 would work for you, but to be certain you will want to measure the diameter of the grease cap hole. If it is 1.18…

view full answer...

Answer 4

The Erickson Horizontal E-Track, part #E19148 has 1/4 inch diameter mounting holes spaced 2 inches apart. The screws you use should be at least long enough to go 3/4 inch into the wood you are mounting the track to. The more screws you use the more…

view full answer...

Answer 5

E-track can be driven over and it will be fine. It would not collapse or otherwise damage itself. You could use and drive over the Erickson Horizontal E-Track #EM19147. Then for a wheel strap the Erickson E-Track Wheel Tie-Down Strap with Roller…

view full answer...

Answer 6

It is not required to install a washer between the outer bearing and the castle nut on the Trailer Idler Axle Beam with Easy Grease Spindles part #e48GR. That said, it's not a bad idea to use one and I recommend this to ensure there is no damage…

view full answer...

Answer 7

The EZ Lube Spindle features includes a zerk fitting in the end of the spindle and holes in the spindle that allow grease to be injected into the hub bore. The only difference between the hubs we sell for an EZ Lube spindle and a standard spindle is…

view full answer...

Answer 8

An EZ lube spindle will be better because it allows you to insert grease from inside the spindle where the bearings are and push out the old grease whereas with a Bearing Buddy you basically just get to push grease through the front of the hub. I…

view full answer...

Answer 9

Most likely a 1-7/8 inch or 2 inch hitch ball would be needed for your 5 by 8 foot Snowbear utility trailer. I attached a page that has all of the hitch balls we have. You'll want to look on top of coupler of your trailer and you'll see the…

view full answer...

Answer 10

Since trailer manufacturers do not make bearing information readily available to the public you would need either the bearing numbers from the bearings themselves or measure the spindle to know which bearings would fit. If you pull the hubs off and…

view full answer...

Answer 11

As SnowBear trailers are still being produced, and haven't been around long enough for any of the weird/rare spindle options, you will not need to measure anything else to confirm the fitment of the etrailer.com Trailer Idler Hub Assembly…

view full answer...

Answer 12

You can actually measure the bolt pattern of a wheel in either way that you mentioned. I attached a picture that shows how to measure across center of the wheel to determine the bolt pattern but if you have a 5 lug bolt pattern you can also measure…

view full answer...