Can a Load be Put On Top of E-Track

Question

Question:

Can u put a load on top of e track

asked by: Jason C

0

Expert Reply:

Yes, if you needed to place items on top of E-Track such as # E19148 you can. I would stay within its rated capacity though which is 2,000 pounds working load limit. This would be assuming the weight is evenly distributed.

expert reply by: Michael H

0

Answer 1

As long as your 5 flat pin supplies brake signals from the brake controller you will be good to go. The purple (reverse) and black (12 volt) wires are not necessary and can be tied up out of the way. You will also need a 7 to 5 way adapter like…

view full answer...

Answer 2

Erickson E-Track should be secured to the mounting surface with no fewer than 2 fasteners per linear foot per side, so for example a 3-foot section would need no less than 8 fasteners. The type and length of fastener depends on the mounting surface…

view full answer...

Answer 3

For an end cap for the horizontal e-track the part #ET8730 would give the track a more finished look. You can mount the E-Track Trailer Cargo Control, #EM59150, using wood screws if the mounting surface is wood. If it is sheet metal, I would use…

view full answer...

Answer 4

Yes, the CargoSmart Rope Ring part #3481767 is compatible with the Snap-Loc E-Track Tie-Down Anchor part #SLSS. The safe working load limit of the Snap-Loc E-Track Tie-Down Anchor is 1,000 lbs even if you use the 2,000 lb CargoSmart Rope Ring you…

view full answer...

Answer 5

Yes, the Erickson Horizontal E-Track part #E19148 will be plenty strong enough to secure your two rock crawler buggies. The tracks are each rated at 6,000 lbs max break strength and 2,000 working load limit. I assume you would have a track under each…

view full answer...

Answer 6

I may have a solution for you, but we don't have any angled trim that is 1-1/2" x 1". The closest available angled trim we currently have available is the Angle Trim for Enclosed Trailer - 93-1/2" Long x 3/4" Tall x…

view full answer...

Answer 7

We carry the part #IMF18800-87 which comes with two ratchet straps that have one end that will connect to the etrack and the other end has a hook on it. I attached a review video for you to check out as well. I attached a review video for you to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Can a Load be Put On Top of E-Track

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching