Can Roadmaster Hitch Mounted Spare Tire Carrier Hold 38 inch Wheel and Tire

Question

Question:

I am looking for a solution for a spare tire carrier for my Ford E350. I have 38inch tires and wonder if they would fit. I would also need the adapter for the rim offset.

asked by: JIm

1

Helpful Expert Reply:

The Roadmaster Hitch Mounted Spare Tire Carrier w/ 2" Receiver Opening # RM-195225 that you referenced will work for you as it can fit all bolt patterns and has a 400 lb vertical weight capacity. Your 38 inch tires would not be an issue.

expert reply by: Jameson C

1

Answer 1

We do have one spare tire carrier you might be interested in. I recommend the Roadmaster Hitch Mounted Spare Tire Carrier #RM-195225. This carrier fits in the 2-inch receiver at the back of your truck and can carry your spare so you can have full…

view full answer...

Answer 2

The Roadmaster Hitch Mounted Spare Tire Carrier #RM-195225 is compatible with 2" receivers so if that is what you have on your 2016 Thor Palazzo then it will fit. The carrier fits with wheel sizes 16" - 24-1/2" so it will…

view full answer...

Answer 3

The Roadmaster Spare Tire Carrier part #RM-195225 is compatible with wheel sizes that are between 16 and 24-1/2 inch in diameter and fits all bolt patterns so your size of 195/75-16 would easily be compatible.

view full answer...

Answer 4

The Swagman Quad 2+2 S64692 has a measurement of 17-1/4 inches from the center of the hitch pin hole to the closest wheel tray. The shank raises at the 10 inch point. To get your swing away, I recommend the Yakima BackSwing #Y02483 which is 14-1/2…

view full answer...

Answer 5

Thank you for all of the info! Long story short I recommend using the Kuat Pivot 2 #PVD20B that swings to the driver's side of the vehicle. It accomplishes what you're needing done, is a solid piece of hardware, is the easiest to use, and it…

view full answer...

Answer 6

The Kuat Pivot 2 Swing Away Hitch Extender for Bike Racks - 2" Hitches - Passenger's Side #PVP20B is a more common fit because it swings to the passenger side instead of the driver's side like #PVD20B you asked from. To get the…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

The main difference between the Roadmaster Hitch Mounted Spare Tire Carrier item #RM-195125 and item #RM-195225 is the size of tire and increased capacity for flat towing. Item #RM-195125 tops out at 6,000 lbs and is limited to a 16-1/2" tire…

view full answer...

Answer 11

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...