Replacement Yates Blue Roller with 5 Inch Diameter and 3 Inch Width

Question

Question:

I am looking to replace 20 existing Yates Blue rollers with the number 500 embossed with a black core. Dimensions are 5inch dia X 3inch wide. The inside diameter of the core is 1.38inch The outside diameter of the shaft is 1.37 What is the correct part number for this roller

asked by: Jim B

0

Expert Reply:

The closest option we have to the measurements listed in your question is with the Yates Ribbed Wobble Roller # YR500BW-9P. This roller has a 5 inch diameter and is 3 inches wide. The dimension that is slightly off from what you mentioned is the center hole diameter, which is just slightly under 1-1/4 inches on this model. It is designed for use with a 1-1/8 inch diameter shaft. This roller does also have "500" embossed on the unit that you can see in the picture I attached.

We do not have a matching size roller that features a larger center hole.

expert reply by: Chris R

0

click to enlarge

Answer 1

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…

view full answer...

Answer 2

On the shaft of your LoadRite boat trailer you will want to measure the diameter of the shaft at the widest point, which is probably the top to bottom of the curved part of the shaft. It should measure 1-1/8 inches for the Yates TPR Ribbed Wobble…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Replacement Yates Blue Roller with 5 Inch Diameter and 3 Inch Width

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching