Accessing 2014 Grand Cherokee Electric Brake Wiring

Question

Question:

Hello, Quick question about the location of the factory installed wiring harness. Mine is extremely difficult to access as it seems to be zip tied to other wires. Should the harness slide out of the zip ties or should I cut the ties off? I dont want to cut if it should slide out. Thanks

asked by: Eric P

0

Expert Reply:

You can cut the zip tie that is holding the factory brake controller connector for your 2014 Jeep Grand Cherokee to make it easier to access. If you wanted to make the connection to the # TK93VR and then use another zip tie to put it back up where it was you certainly could.

I attached an install video for this harness that shows it installed on a similar 2014 Grand Cherokee as yours too.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Yes, in order to install the Tekonsha Prodigy P3 Trailer Brake Controller part #90195 on a 2015 Jeep Grand Cherokee you can use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part #TK93VR for a plug-in-play installation. I have…

view full answer...

Answer 2

The Tekonsha Plug-In Wiring Adapter item #TK93VR is the same harness as the 3045-P. Item #TK93VR is the updated model number. Both will allow you to install a Tekonsha Brake Controller like the Tekonsha P3 item #90195 in your 2019 Jeep Grand…

view full answer...

Answer 3

I'll begin with the assumption that you have a 2015 Jeep 'Cherokee Latitude, as the Renegade and Compass Latitude weren't equipped with the optional factory 7-way. The brake controller connector is located behind the black…

view full answer...

Answer 4

Measuring to find the right rise or drop needed to tow the trailer level is easy. First park the truck and trailer on level ground and uncouple the trailer from the truck. Use the trailer's jack to make the trailer level. Measure from the ground…

view full answer...

Answer 5

The brake controller install harness on your 2022 Jeep Grand Cherokee 4xe is under the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. The Tekonsha brake controllers like the Prodigy P3 part #90195…

view full answer...

Answer 6

I looked up the trailer connector wiring diagram for a 2007 Ford F-250 which should be the same as a Ford F-350 and found the 7-way trailer connector to contain the following wires: Orange = 12 Volt Power White = Ground Black/Green = Reverse Blue =…

view full answer...

Answer 7

Yes, you are looking for part number, #90195 for the Tekonsha Prodigy P3 Trailer Brake Controller and need the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers, #TK93VR too. This adapter plugs into the 4-pin connector on your…

view full answer...

Answer 8

Hi Andrei; yep, you're 100 percent right, you should use the 30 amp breaker. That's why for the installation kit I recommend using the Universal Installation Kit for Trailer Brake Controller #ETBC7. The #ETBC7 comes with multiple breakers,…

view full answer...

Answer 9

I have a solution for you, but the #LC379145 is not the correct motor replacement for a PowerGear 903209000. According to my tech contact at Lippert, the correct replacement motor is the Replacement Lippert Components 5:1 Gearbox With Motor for RV…

view full answer...

Answer 10

Your National seal 413470 has an outer diameter of 3.376 inches and an inner diameter of 2.125 inches. For a replacement we have #GS-2125DL for one seal or #RG06-090 for a pair. These are all double lip seals.

view full answer...

Answer 11

For your 2015 Jeep Grand Cherokee I recommend the P3 brake controller, #90195. This is a proportional controller that will apply the trailer brakes in proportion to how much the Jeep is braking. this is the safest way to stop and it reduces wear and…

view full answer...