Camper Steps for 24 Inch Doorway and 24 Inch Height

Question

Question:

I am interested in purchasing a Solid Step set of camper steps for a Northwind camper. It has a 24inch door opening and a 24inch to the ground on a level surface. Does etrailer offer these steps and what is the part number please? Thanks,

asked by: Gary F

1

Helpful Expert Reply:

There are steps that can work for your Northwind camper and I recommend checking out the Brophy Camper Scissor Steps # SS03 which is a triple step that will work with your 24" height.

These are not permanently mounted; instead you install a mounting bracket to your camper and then attach the stairs after reaching your destination.

I have added a photo from a customer who has these steps installed as well as a link to a video review.

expert reply by: Kyle S

1

click to enlarge

Answer 1

The extended vertical height of the Scissor Steps part #SS03 is 30 inches from the top bracket. Based on that this product should work very well for what you are doing since the height you are looking for steps for is 35-36 inches.

view full answer...

Answer 2

The Brophy scissor steps #SS03 are steel with a black powder coat. Steel can rust if it is exposed to the elements. Eventually the powder coat can get chips or scratches in it exposing the steel and then it can start to rust. If you notice scratches…

view full answer...

Answer 3

Steps like the Scissor Steps #SS03 come with a bracket that gets permanently mounted to the camper, but the steps themselves get removed while traveling.

view full answer...

Answer 4

The Brophy Universal Mount Steel Scissor Steps #SS03 have a height when extended of between 24- and 30-inches. You can measure your truck's bed height to see if this will allow the bottom cross piece (below the lowest step) to reach the ground…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Hello Dave, glad to hear you like our videos. Since you will be hauling more of a constant load like a truck bed camper, I definitely recommend going with the Heavy-Duty RAS Kit #RAS3611-YHD. The regular duty kit is recommended for light to medium…

view full answer...

Camper Steps for 24 Inch Doorway and 24 Inch Height

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching