Do the Scissor Steps # SS03 Get Removed from RV When Traveling

Question

Question:

Hi There, Is the mounting bracket and steps designed to remain attached to the camper while driving? Or is it recommended to remove the steps prior to driving? Thank you for your assistance.

asked by: Allan

0

Expert Reply:

Steps like the Scissor Steps # SS03 come with a bracket that gets permanently mounted to the camper, but the steps themselves get removed while traveling.

expert reply by: Jameson C

0

Answer 1

Your 2016 Wildwood camper was made by Forest River which typically uses Lippert frames, so the Lippert pull out steps part #LC432682 should work well for you. However, you can measure your current steps and compare them to the dimensional pictures I…

view full answer...

Answer 2

There are steps that can work for your Northwind camper and I recommend checking out the Brophy Camper Scissor Steps #SS03 which is a triple step that will work with your 24" height. These are not permanently mounted; instead you install a…

view full answer...

Answer 3

The Brophy Universal Mount Steel Scissor Steps #SS03 have a height when extended of between 24- and 30-inches. You can measure your truck's bed height to see if this will allow the bottom cross piece (below the lowest step) to reach the ground…

view full answer...

Answer 4

The extended vertical height of the Scissor Steps part #SS03 is 30 inches from the top bracket. Based on that this product should work very well for what you are doing since the height you are looking for steps for is 35-36 inches.

view full answer...

Answer 5

The Brophy scissor steps #SS03 are steel with a black powder coat. Steel can rust if it is exposed to the elements. Eventually the powder coat can get chips or scratches in it exposing the steel and then it can start to rust. If you notice scratches…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Do the Scissor Steps # SS03 Get Removed from RV When Traveling

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching