Is It Possible to Just Replace Trailer Axle Spindle if Axle is Still Good

Question

Question:

I have weld on spindles/ axle stubs that need replacing. My question is can I reuse the axles if they are in good condition?

asked by: Al

0

Expert Reply:

If your axles are fine you can replace just the spindle and be totally fine. This is a common enough situation which is why we offer just replacement spindles like the part # TRU97FR that you were looking at.

Trailer spindles must be installed by a qualified professional welder. Spindles must be welded on perfectly concentric or you will have tracking problems. A trailer shop will have the right jigs to allow the spindle to be welded on correctly.

expert reply by: Jameson C

0

Answer 1

To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel…

view full answer...

Answer 2

Replacement of a spindle on a trailer axle is best left to a professional installer. This is not a do-it-yourself type of project. We urge you to use a professional welder experienced in axle fabrication. Proper alignment and welding are critical…

view full answer...

Answer 3

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure…

view full answer...

Answer 4

It might seem that the spindle being slightly bent isn't a big deal but it can definitely lead to another blowout so you'll want to replace that spindle with a new one. It looks like you have a straight spindle like the standard BT8 found as…

view full answer...

Answer 5

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 6

From my research it looks like the correct replacement seal for your Reliable oil bath kit is the Replacement Seal #XLPROLUBE1980SEAL which is used for 3,500 lb axles. This seal has a 1.72" inner diameter and a 2.56" outside diameter. You…

view full answer...

Answer 7

The Bearing Kit #BK2-100 will contain the new bearings, races, grease seal, tang washer and cotter pin for replacing the bearings on your 2005 Ranger Trail Boat Trailer. The Inner Bearing #L68149, Inner Race #L68111, Outer Bearing #L44649 and Outer…

view full answer...

Answer 8

The #XLPROLUBE1980KIT is compatible with a 3500 lb spindle that uses the L68149 inner/L44649 outer bearing and the 171255 grease seal, so it'll work great for you. You can view a product description video by clicking the provided link.

view full answer...

Answer 9

In all honesty, you're almost certainly going to be best off by replacing the axle. The spindles are likely gouged in the locations where the bearings ride. The act of sanding out the damaged area of the spindle has likely removed some material…

view full answer...

Answer 10

Grease can ooze out of the opening unless you temporarily plug it with something. I would advise not to tow the trailer until you can get a new grease fitting installed. The Sure Lube manufacturer may have a specific replacement for the system. If…

view full answer...

Answer 11

It sounds like the zerk fitting on your spindle has failed as it is not supposed to go into the spindle. You will want to remove the zerk fitting somehow because it could interfere with the possible solution of using bearing protectors, #KREB1980AC,…

view full answer...

Answer 12

The Kodiak XL ProLube Kit #XLPROLUBE1980KIT can be used in place of your Grease Seal #58846(2.565" OD, 1.719" ID) if you are converting your hubs to oil bath. The Seal #XLPROLUBE1980SEAL for oil bath hubs will require you to replace your…

view full answer...

Is It Possible to Just Replace Trailer Axle Spindle if Axle is Still Good

Product Page this Question was Asked From

Continue Researching