Replacement Keys for Lippert Slam Locks on 2011 Heartland Landmark 5th Wheel Trailer

Question

Question:

I am needing a replacement set of keys for my Heartland Landmark 2011 5th wheel. The original keys were stolen out of my truck. The compartments are Slam-Latch.

asked by: Renee L

0

Expert Reply:

The Replacement Keys for Lippert Components Slam Latch Baggage Door Handle - Qty 2 # LC230012 are the correct replacements for Lippert Slam Latch.

If you wish to increase your security, you can use the Global Link RV Baggage Door Slam Latch with Keyed Alike Option - Black - 1-3/4" Thick # 295-000078 and select keyed alike to get replacements that are all keyed alike but locks that can have hundreds of different keys versus the Lippert part that are all keyed alike.

expert reply by: Jason S

0

Answer 1

If you have a Lippert Slam Latch Baggage Door Handle then they all use the same key which is the Replacement Keys for Lippert Slam Latch Baggage Door Handle part #LC230012. There's usually a brand on a sticker inside the latch so if you have…

view full answer...

Answer 2

There is a replacement key for the Southco Slam Latch made by Lippert. You will need replacement key #LC230012. All of the keys are the same that unlock this latch. If you have this latch this key will work for it.

view full answer...

Answer 3

For Slam Latch baggage door locks use #LC230012 for factory Lippert latches.

view full answer...

Answer 4

The lock code could be located on the key itself, on the face of the lock core, or one a sticker attached to the lock (see photos). Once you find this you can then order the correct replacement key assuming you have a Global Link, Fastec (FIC),…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...