Replacement Landing Gear Legs for 1995 Jayco Designer Series 5th Wheel Trailer
Question:
I have a 1995 Jayco Designer Series 3210RLR fifth Wheel camper that I am needing to purchase landing legs for. The gears have worn out and I have discovered the replacement gears are no longer available. The legs are bolt on and have the electric motor. What legs will work with this camper.
asked by: Bruce W
Expert Reply:
It looks like your 1995 Jayco Designer Series 5th Wheel Trailer was equipped with an Atwood landing gear system. Atwood was recently bought out so their products are getting harder and harder to find.
To replace both the legs on your system the Lippert # LC179013 Lead Leg and # LC179014 Follow Leg should work great. These feature standard weld stop measurements of 15-1/2 inches from inside to inside and 17-1/2 inches from outside to outside. You will just want to compare this to your existing brackets to make sure these will bolt right up without any modification. I have attached an image to clarify this.
I have attached a couple short video demonstrations that you can also check out.
Products Referenced in This Question
Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Driver Leg
- Lippert
more information >
Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Follow Leg
- Lippert
more information >
Product Page this Question was Asked From
Follow Jack Repair Kit for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Repair Kit
- Stromberg Carlson
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Suspension Enhancement
- Shop: Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs
- Q&A: Recommended Replacement Landing Gear For 1996 Jayco Eagle 5th Wheel Camper
- Video: Rebuilding the etrailer and Ram Square Jacks
- Shop: Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 5,000 or 7,000 lbs
- Shop: Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Shop: Replacement 5th Wheel RV Landing Gear Follow Leg w/ Snap Pin for RVs
- Video: Stromberg Carlson Landing Gear Replacement Lead Leg Review
- Video: Review of Lippert Components Camper Jack Parts - Landing Gear Lead Leg - LC119102
- Q&A: Will Lippert Landing Gear # LC179013 and # LC179014 Fit a 2008 Wildcat 5th Wheel Trailer
- Q&A: Replacement Landing Gear Set for 2010 Jayco Super Lite 31.5 FBHS
- Q&A: How to Determine Correct Replacement Lead Leg for Landing Gear
- Shop: Replacement Follow Leg for Stromberg Carlson Landing Gear - 33-1/2"
- Shop: Replacement Follow Leg for Venture 5th Wheel RV Landing Gear
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Search Results: air bags
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Article: Trailer Tire Sizing
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: hitch
- Search Results: timbren
- Shop: Fifth Wheel Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Article: Most Popular Wheel Bearings
- Search Results: sumosprings
- Shop: Gooseneck Hitch
on Accessories and Parts
Debra O.
8/9/2020
I have a 1997 jayco designer 3510 and atwood 71125 landing gear the gears went out of the legs and there is no replacement gears is there any legs that can be purchased to work with the landing gear.