Hardware to Install the Replacement Locking Ratchet Arm Assembly Part # 753-3579

Question

Question:

Can I use the lock and nylon screw from my ratcheting arm I am replacing?

asked by: Billy

0

Expert Reply:

Yes, you can use your existing hardware to install the Replacement Locking Ratchet Arm Assembly part # 753-3579. However, I would go to the local hardware store and purchase a new nylon insert lock nut as they are technically a one time use only product but I am sure you would be fine using you old nut. You will also need part # 853-1251 in order to transfer the lock core over.

expert reply by: Conner L

0

Answer 1

It sounds like you're looking for the: -Replacement Locking Ratchet Arm Assembly for Thule T2 Hitch Bike Rack or Sidearm Roof-Mount Rack #753-3579 . This ratcheting arm assembly is a direct replacement for your Thule T2 Bike Rack, and is the part…

view full answer...

Answer 2

The two parts you mentioned would be all you'd need, part numbers #753-3579 and #753-3583 as they appear to be the only parts that are damaged and the rest could be swapped over as needed.

view full answer...

Answer 3

Based on the picture you submitted and the description of what is wrong with your rack it looks like you referenced all of the parts you would need to replace on your Thule T2 Bike Rack part #TH9045. Replacement Spar and Pivot Tube is no longer…

view full answer...

Answer 4

The longer arm that is offered for the original Thule T2 is the Replacement Lockable Ratchet Arm Assembly for Thule T2 Bike Racks item #752-1272-001. It is 31-1/2 inches long overall which is about 2" longer than the original item #753-3579. I…

view full answer...

Answer 5

I spoke with my contact at Thule regarding the Locking Ratchet Arm Assembly #753-3579 referenced in your question. He stated that it does not appear that the replacement part has had any recent upgrades, but it will also depend on which particular…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...