Landing Gear Replacement for 2005 StarCraft Homestead Rancher 5th wheel 290RLR
Question:
So I was packed up and ready to leave camp... I hit the switch to raise my 5th wheel, when a clunking sound coming from inside the front hatch caused me to take a look at the landing gearbox and motor. It was dusk, I had no glasses on, but it was clear the motor was hopping and the sound was not right. The mechanic that just finished my brakes said he owned a 5th wheel and offered to help. The legs were not moving, and he said he could crank them manually. the fact I am a single female shouldnt be a factor, but I personally did not believe it would be possible for me to crank a 3+ ton trailer up! Although i had heard of it being done online Unfortunately, he did it wrong and took 2 pipe wrenches placing them on the bar that adjoins the legs and just as he was readying himself to crank I caught view of what he was about to do and I yelled NO! If u try to crank there its going to bend that bar! Isnt it?inch I didnt know HOW to manually turn the legs, so I allowed him to slide the wrenches closest to the gearbox. Then SNAP! AS SOON AS HE WRENCHED ON IT.. we both acknowledged that something snapped. I thanked him for helping and waited till daylight. I found 1/2 of a hex bolt no nut that I believe, should have been a shear pin? laying right below the spot for it in that adjoining square bar. I could only get the front of the gearbox off, yet... I could see no sign of broken gears!? Now, if I understand correctly...the pressure from the weight of the camper is preventing me from being able to remove the rest of it? So! The real question I have is... How do I know WHAT EXACTLY the original AND end result problem is?? Realizing what I believe should be a shear pin .was one of them. In the mean time, I used a jack and several 2x6 scraps to jack and layer 1 on each side at a time till I could hitch up and get myself somewhere to do the repairs. Not realising till after, I am probably going to need the 5th wheel hitched to the truck in order to get the pressure off the legs?? I used a mirror to try and see where the back of the gearbox attaches to the leg but its awfully crowded in there and I cannot see what I am looking for.
asked by: Misty
Expert Reply:
Sounds like a gear box was broken initially but not the jacks are most likely damaged internally after they were were pried on with a long bar. At this point it's probably going to be best to just replace the entire setup. Did the gear box look like the # LG-179015 that you referenced? If so, this is a very common setup and you could use the # LG-183708 as a replacement setup.
Feel free to send me pictures of your landing gear and I should be able to recognize it and get you exactly the kit you'd need otherwise if the # LG-179015 is not what you need.
Products Referenced in This Question
Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Product Page this Question was Asked From
Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Gearbox
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Lippert Replacement Motor Harness for RV In-Wall Slide-Out - 25' Long
- Shop: Bearing Kit, L44649 Inner/Outer Bearings, 10-9 Seal
- Shop: Lippert Replacement Motor Harness for RV In-Wall Slide-Out - 20' Long
- Shop: Propane Hose - 3/8" Female SAE Swivel x 3/8" Male NPT - 2'
- Shop: Replacement Hardware Kit for Fastway e2 Weight Distribution Head - Round and Trunnion Bar
- Shop: Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs
- Shop: Global Link RV Entry Door Locking Latch Kit with Keyed Alike Option - White
- Search Results: apubr~8
- Search Results: e27sr
- Search Results: 8327816~eb
- Search Results: 2.5 inch weight distribution shank
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Q&A: Seal With Dimensions to Replace 171255UC
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: Replacement Clearance Lights Needed for GLO-BRITE 122R and 122Y Lights
- Video: Choosing the Right Trailer Wiring
- Search Results: 68149
- Shop: Fifth Wheel Hitch
- Video: Aries AdvantEdge Headache Rack Review
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Article: Trailer Tire Sizing
- Search Results: dust cap
- Q&A: How to Measure Hub Face of Mobile Home Hub and Drum
- Video: Review of Gen-Y Hitch Dual Sway Control Bracket Adjustable Ball Mount 2" Receiver - 325-GH-300-1
- Shop: Gooseneck Hitch
- Article: Most Popular Wheel Bearings
- Article: How to Choose the Right Trailer Hitch Class