What is Included with Trailer Hitch # C11356 for a 2016 Mazda 6
Question:
I was looking at the 5inch draw bar but nto sure which one i need? What size is the standard draw bar? Also does the ball come included?
asked by: Bernardo C
Helpful Expert Reply:
The recommended ball mount for Curt trailer hitch receiver, part # C11356, is 9-3/8 inches long with 2-5/8 inches of rise or 3-1/4 inches of drop. It's part # C45016.
If you prefer a draw bar with 5 inches of rise use part # C45014. The hitch ball is not included so you can use part # A-82 for a 2 inch ball or part # A-80 for a 1-7/8 inch. They'll fit both the included and the other draw bar I mentioned and # F-4 is the pin and clip that fits.
You also need a wiring harness to power the trailer's lights. Use part # 118587 which installs by plugging in behind both tail lights inside your trunk. Then there's a wire that needs to be run to the vehicle's battery through the included fuse.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 5 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Hitch for a 2024 Honda CR-V Hybrid
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Trailer Hitch Recommendation for 2017 Mazda 6 for Carrying Thule T2
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What Tool is Normally Used for Torqueing Down Hitch Balls
- Q&A: How To Install A 2-5/16 Inch Hitch Ball To A Draw Bar That Has Limited Access to the Hitch Ball Nut
- Q&A: Gaining Rise With a Hitch Ball
- Q&A: Hitch Recommendation for a 2015 Mazda 6
- Q&A: Choosing Hitch Thats Most Concealed for 2015 Mazda 5
- Article: How to Strap a Bike To a Roof Rack
- Article: Trailer Hitch Receiver Sizes
- Article: Trailer Hitch Installation Tips
- Article: How to Choose a Bike Rack for a Sedan or Hatchback
- Article: How (and Where) to Connect an RV Propane Grill