Where Does Safety Bolt of Trailer Valet 5x Install

Question

Question:

I just installed a Valet 5X, but can’t see where the safety bolt goes 21B. Can you help?

asked by: Jim B

1

Helpful Expert Reply:

It sounds like you are referring to the security bolt which is part 21b in the attached diagram. The security bolt was designed to keep the Trailer Valet part # STC-V211 in place when the device is rotated to the stow position, and as an extra safety precaution to prevent theft. It does not inhibit the device from being used properly. If you plan to remove the Trailer Valet after every use then you have the option of not installing the bolt and keeping it somewhere safe. Should you choose to install the safety bolt you will want to take a look at the 3:00 mark in the attached video.

expert reply by: Jameson C

1

Answer 1

I recommend first checking the volume and zone controls, it may be as simple as the zones being turned off so you're getting no sound inside/outside. You can also try resetting the unit by pulling the fuse in the back of the unit next to the…

view full answer...

Answer 2

The Furrion RV Stereo #DV3300SBL can be paired to your smartphone by completing the following steps: 1. Activate Bluetooth mode on your mobile device. Then press the Bluetooth button on the front panel of DV3300S to enter pairing mode. 2. When…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...