Replacement Tarp Recommendation for 2005 Ford F-150 Short Bed with Truxedo Lo Pro QT

Question

Question:

I did find a sticker on the driver's side rail. The only number on it was PN1113645. It is a 6 1/2 foot bed. I hope this helps you point me in the right direction for a replacement tarp. Thanks

asked by: Al

0

Expert Reply:

We carry replacement Truxedo tarps but I need to know which model you have specifically to pick out what you need.

expert reply by: Jameson C

0

Al

7/17/2018

I did find a sticker on the driver's side rail. The only number on it was PN1113645. It is a 6 1/2 foot bed. I hope this helps you point me in the right direction for a replacement tarp. Thanks

Reply

Jameson C.

7/17/2018

I spoke to my contact at TruXedo and they were able to reference the number you found on the drivers side rail (1113645) as being part of a TruXedo Lo Pro QT Soft Roll-up Tonneau Cover. The cover you have is the part # TX578101. So the replacement tarp you need is the part # TX1117655.

Reply

Answer 1

You can possibly find a tag with information for your TruXedo cover up under the cover towards the driver's side. If you don't find anything there then you can simply let me know what the year/make/model of your vehicle is as well as the…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...