Economically Priced AC Unit Recommendation for Trailer Not Ducted for AC

Question

Question:

I have a 7X16 slantnose trailer that I use to store and move sailing gear. I am going to bring the trailer to Tampa this winter and think I need to add air conditioning. What is the best, most cost effective option? Do you sell kits?

asked by: Jeremy A

0

Expert Reply:

Since the trailer does not have ducts built into it for AC venting you'll want a non-ducted AC unit like the # ACM135C which would work well. This is our best priced kit that comes with everything needed to install.

expert reply by: Jameson C

0

Answer 1

You are most likely going to have to replace your entire jack. In my experience the motor is typically one part when it goes on on a trailer tongue jack the manufacturer does not carry any replacements. I recommend replacing it with the Bulldog…

view full answer...

Answer 2

We do have a potential option for your with the ARK Xtreme Off-Road Swing-Up Trailer Jack #ORJW750BD. We do not offer any thing with a foot plate that will fit your parameters. So if you are willing to use a jack with a dual wheel, this will be a…

view full answer...

Answer 3

The Fifth Wheel and Gooseneck 90 Degree Wiring Harness with 7-Pole Connector, Chevy, Ford, GMC, 9 foot, item #50-97-410, is designed to plug directly inline with the original factory 7-way connection under your pickup bed. You will retain the use of…

view full answer...

Answer 4

For your 2006 Keys Trailer, I recommend going with the: -Advent Air RV Air Conditioner System #ACM135C for a white unit, or #ADV44FR for black. These are 13.5K Btu units that is compatible with ducted or ductless systems, a 6-blade fan with three…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...