Recommended Frame Mounted Camper Tie Downs for a 2005 Dodge Ram 3500 4x4 Long Bed

Question

Question:

This is a 2005 Dodge ram 3500 4wd. The front s to fit. But the rear is the superhitch for a 2013 Ram that got put on it. Regarding the tie downs for superhitch: I only have a pair of straight s and wondering what the sleeveinch if you call it that would cost for the Dodge R3507 type that goes on the superhitch? The piece that bolts to the hitch that the would slide into. I also have the part that bolts to the front of the truck frame, but no s. Those have that bend in them. What would a pair of them cost?

asked by: Joyce

0

Expert Reply:

The correct set of frame mounted tie downs that will fit your 2005 Dodge Ram 3500 with the TorkLift SuperHitch Magnum Trailer Hitch Receiver part # TLD1108-30 is the TorkLift Custom Frame-Mounted Camper Tie-Downs part # TLD2101 if you have running boards/nerf bars or part # TLD4101 if you do not have running boards/nerf bars for the front and the TorkLift Custom Frame-Mounted Camper Tie-Downs part # TLR3503 for the rear.

Unfortunately, we do not have any replacement parts for the frame mounted tie downs so I would have no way to make the TorkLift Custom Frame-Mounted Camper Tie-Downs part # TLR3507 work on your truck.

expert reply by: Conner L

0

Answer 1

You can use a hitch extension but it will reduce your trailer hitch tongue weight capacity by 50 percent. We don't have a 2 inch hitch extension compatible, so I recommend a 2-1/2 inch hitch for your truck and get the Titan Hitch Box Extension…

view full answer...

Answer 2

To use the Torklift hitch extender part #TLE1542 that you referenced your truck will need to have a Torklift hitch installed on it that has dual hitch openings like the #TLD1108 which fits your truck and gives it a second hitch opening under the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The Class V hitch we have for your 2004 Dodge Ram 2500 with the best ground clearance is the Curt hitch part #C15809. It doesn't tuck right under the rear bumper like what you can see in the attached picture but it does sit the highest.

view full answer...

Answer 10

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Answer 11

Thanks for the pictures but no, the EX2700 tonneau cover that the #EX1700 fits is for a 2004-15 Nissan Titan 6' 7" Bed. The one previously mentioned #EX1770 is for your truck, so it'd for sure work if you have the 2770 tonneau cover.

view full answer...

Answer 12

In regards to HappiJac Truck-Mounted Camper Tie-Downs like part #LC182908-182928, the front tie-down installs inside the bed on the front panel directly behind the cab. The rear tie-down then mounts to the bumper. They will not require removal of the…

view full answer...

Recommended Frame Mounted Camper Tie Downs for a 2005 Dodge Ram 3500 4x4 Long Bed

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching