What Part of Weight Distribution System Can be Swapped Between Brands

Question

Question:

Do any of your trunion bar heads interchange with a quality S spring bar.

asked by: Steve

0

Expert Reply:

Some parts of weight distribution systems can be interchangeable between brands, but not heads and spring bars. We have no parts for Quality S products. These will be brand-specific and can even be product line-specific too, working with only one particular style of system from a given maker.

Shanks like # C17123 all use standardized hole size and spacing so this particular item in a WD setup if perfectly fine to swap to another brand if needed.

expert reply by: Adam R

0

Answer 1

The internal channel width of the Replacement Shank for Curt Adjustable 2-Ball Mount #C45917 is 3" while the Replacement Ball Platform #C28KR you're looking at has a 2-3/4" width and is for the Curt Rebellion XD rated only…

view full answer...

Answer 2

We do have the Replacement Ball Platform for Curt Rebellion XD Adjustable Ball Mount part #C28KR available. I think it is a great idea to have the seperate platforms rather than going through the entire swapping and torquing of the balls for each…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 6

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 7

I would love to help but I can't really tell you if you need the B&W Tow & Stow 2-Ball Mount with 5" Drop part #BWTS20037B (part #BWTS20037C) or 7" Drop part #BWTS20040B (part #BWTS20040C) as it varies by application so you will…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Your 2024 Chevrolet Silverado 3500 will come with a 2-1/2" trailer hitch receiver. If your truck did not come with a reducer for a 2" receiver we do have the B&W #BWRHXA2182 if you need to use your 2" ball mount or hitch mounted…

view full answer...

Answer 12

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...