Will Brophy Camper Tie Downs # HSSF Work With 2009 Dodge Ram 1500 Quad Cab 2WD Truck

Question

Question:

will these work on my 09 dodge ram 1500 quad cab 2wd

asked by: Todd L

0

Expert Reply:

The Brophy Camper Tie Down, part # HSSF is a universal fit item and will work on your 2009 Dodge Ram 1500 2WD Quad Cab. There is not a weight capacity for the hold downs, and will work with any camper that fits your truck.

Part # HSSF works with trucks that have spray-in bedliners. If your truck has a drop-in bed liner, it will need to be trimmed or removed to use part # HSSF.

The Brophy Tie Down mounts over the sidewall of the truck bed. The recommended hardware kit to install part # HSSF is Camper Tie Down Hardware Package, part # TDHP.

expert reply by: Reno H

0

Answer 1

For a set of camper tie downs that attach to the bed of your 2015 GMC Sierra 1500 I recommend the #HSSF. These tie-downs use a clamp-on mounting system that grabs the underside of your bed rails. I have attached a photo that shows how this system is…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 8

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 9

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 10

The Brophy Slide In Camper Tie-Downs #HSAB might be a fit for your 2011 Ford F-150 but you'll need to do a bit of measuring first and you'll likely need to trim out holes where the tie-downs would sit. You'll want to verify that #HSAB…

view full answer...

Answer 11

Yes you can absolutely use the HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs #LC182895 with your TorkLift tie downs.

view full answer...

Answer 12

That is correct, you can tap into the plug and it will provide a charge but keep in mind that this is not the most efficient way for charging a battery. This method does not provide any charge balancing or battery charge management and on newer…

view full answer...