How to Test Brake Controller without Trailer Connected
Question:
How to check unit without a trailer. 96 chev.
asked by: Greg
Expert Reply:
All the brake controller needs to sense a trailer connection so that you can test it is a slight amperage draw on the output circuit. For that you can use a circuit tester like the part # PTW2993 with one pin grounded and the other on the output pin. Then you can hit the brake pedal of the vehicle and you should see the brake controller operate like normal. You'll need someone to help since it's hard to be at the rear of the vehicle and pressing the brake pedal. If you can't get the controller to operate normally there is a more in-depth way to test it.
Testing the brake controller is fairly easy. Sever the blue brake output wire near the brake controller leaving enough room to reconnect it and then apply the manual slide. Using a circuit tester like the Quickee Tester, part # 3808, you should get output to the controller side of the wire you severed. If the manual slide activates the trailer brake output wire properly, try the brake pedal. If the brake pedal activates the brake output properly also then the problem is farther back either in the vehicle wiring or on the trailer.
If either the brake pedal or the manual slide are not functioning properly you will need to test the wires going into the brake controller. Make sure you have power entering the brake controller on the black wire. On the red wire you will only want power when the brake pedal is pressed.
If there is power on the red wire before the brake pedal is pressed you have connected the red wire from the brake controller to the wrong circuit. You would then need to find the brake switch wire that has power ONLY when the brake pedal is activated.
If these connections check out and the brake controller is properly grounded then there is possibly a problem inside the brake controller.
I am including a link to a video that will show you how to test the wiring on a brake controller.
Dan
4/8/2024
Jameson, I bought a podigy P3 brake controller and wanted to test it. I cant even set it up because it doesnt see a trailer. so if i use a prob circuit tester clip one end to truck frame and the prob to the blue pin it will have enough amp to see a trailer and i can set it up thanks
Jameson C.
4/8/2024
Product Page this Question was Asked From
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Video: Trailer Brake Controller Wire Testing
- Shop: Hook Probe Circuit Tester
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Article: Trailer Wiring Diagrams
- Article: Testing Trailer Brake Magnets for Proper Function
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires
- Q&A: What Gauge Wire Should be Used to Wire Trailer Brakes
- Shop: Adapter 4-Pole to 7-Pole and 4-Pole
- Video: Choosing the Right Brake Controller
- Search Results: 7 blade rv plug
- Shop: Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers
- Q&A: What is the Best Grease for Trailer Bearings
- Article: Brake Controller Installation: Starting from Scratch
- Shop: Trailer Wiring
- Shop: BOLT brand vehicle and hitch locks
- Shop: Suspension Enhancement
- Video: Tekonsha Prodigy P3 Trailer Brake Controller Installation - 2020 Ford E-Series Cutaway
- Video: Tekonsha Prodigy P3 Trailer Brake Controller Review
- Search Results: trailer wiring
- Search Results: axletek 10 gg
- Video: Deka Jacketed 10 Gauge Wire Installation
- Search Results: 10" brake shoes
- Shop: RV Interior Lighting
- Q&A: How Do You Measure The Height Of An Equalizer?
- Search Results: 12 gauge wire
- Search Results: 10 2 duplex wire
- Video: Review of B and W Trailer Hitch Ball Mount - Tow And Stow 3 Ball Mount 2-1/2 Inch Hitch - BWTS20048B
on Wiring
Michael
4/13/2024
Hi There. great tips. Mine works fine when I use the slide, even while driving and for long periods. As soon as I use the brake pedal it goes to overload. If it trun the power down under 2 it can cope with it. Any thoughts? much appreciated