Can both a 1 Inch Spacer and 1/2 Inch Spacer be Used Together for Timbren Helper Springs

Question

Question:

I understand the TORTUN4 is about 5” installed and I have 7.75” clearance, can I add a Timbren 1” spacer with a 1/2” spacer? I ask because the recommended space is 1” to 1.5” before contact, unloaded. Thanks

asked by: Joshua

0

Expert Reply:

Yes, you can use a 1 inch Timbren spacer, # A25723-90AH00, with a 1/2 inch spacer, # TA25722-90P00, to get to the height you need for your 2015 Toyota Tundra.

expert reply by: Michael H

0

Answer 1

I may have a solution, but most standard 20-lbs propane tanks are 17-3/4" tall and 12-1/4" wide, so the UWS Truck Toolbox #UWS01034 will be just slightly too small since it's only 17-1/4" deep. Instead, you can use…

view full answer...

Answer 2

The best product for your application is the Timbren Rear Suspension Enhancement System (SES) #TTORTUN4. This is very easy to install and does a great job of engaging when under to to help support the OEM suspension on your 2006 Toyota Tundra.…

view full answer...

Answer 3

With Timbrens you want to use a spacer to match as close to the amount of lift you have on the truck if the lift raised the frame of your truck away from the axle of the truck. Since you have a 1.5 inch lift you'd want the 1/2 inch spacer…

view full answer...

Answer 4

Timbren likes to recommend 1 inch between the axle and the Timbren when the truck is unloaded. We have found that this works the best. This allows the suspension to feel when the vehicle is unloaded and still gives you support when needed when…

view full answer...

Answer 5

For a 30 amp circuit you need at least 10 gauge wire like what the Hopkins Toyota 7-Way part #HM43385 has for the 12 volt power circuit. So this will work fine to power your trailer winch.

view full answer...

Answer 6

On your 2004 Toyota Tundra, there are two possible 7-way connectors that could work on your vehicle. Up under the rear of your truck there should be two plugs that you will need to plug in the 7-way. One plug will be connected to your current 4-flat…

view full answer...

Answer 7

There isn't a replacement housing for the #HM43385 that you have so you'll have to replace the entire thing since yours has been damaged. It's easier than you'd think to break them while backing up for sure since they typically hang…

view full answer...

Answer 8

The UWS Chest part #UWS01022 is designed to be used in a cargo carrier outside in the elements. The extra-thick aluminum construction is rust resistant. UWS builds their boxes from sheets of 0.058" thick aluminum. Then they weld the seams for…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...