Height of Bow Stop with 3 Inch Base

Question

Question:

How high is this? The one on my pontoon is a staggering 8inch high and Im looking for the tallest 3inch base stop I can find.

asked by: Mike

0

Expert Reply:

The Yates Y-Style Bow Stop for Boat Trailers # YR6Y33-4 is 3 inches tall. It is 6-1/2 inches span and 2-7/8 inches wide at the base. I've attached a photo and a video to assist. This is the largest bow stop with that base size we have. I've attached the link to the options to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Yes, the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers #AL88211 comes with two separate Schrader valves so that you can air up each air spring individually. If you're also looking for a dual path on-board…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

Hey Scott, I can certainly point you in the right direction for picking out an equalizer upgrade kit for your 2018 Prime Time Tracer Air 275 travel trailer. You will need to measure your wheel base (aka axle spacing) to determine if you need MORryde…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 10

The Blue Ox Apollo Non-Binding Tow Bar #BX7470 is going to be the largest size we have to fit a 2-1/2" receiver. So you will at least need a 3" to 2-1/2" Adapter #C85JR. This will connect to the Base Plate #C56JR on your 2020 Ford…

view full answer...

Answer 11

Hey Jeff, the WeatherTech ImpactLiner Custom Truck Bed Mat #WT99KF would get secured to your bed using the TechHold Retention Device (see image attached) which is just a adhesive ball and socket. Basically, one the ball end would get stuck to the…

view full answer...