LED Trailer Clearance Light Recommendation to Replace Peterson PM-130

Question

Question:

Is there an LED replacement for the PM-130 marker light? Thanks!

asked by: Cézanne R

0

Expert Reply:

Our best option for LED lights to replace your Peterson 130 style lights is the Rectangular LED Trailer Clearance Light, # MCL76AB for amber and # MCL76RB for red. These lights measure 5-13/16 inches long, 2 inches wide, 1-3/16 inches deep, and mounts on 4-13/16 inch centers.

expert reply by: Jameson C

0

Answer 1

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…

view full answer...

Answer 2

If you do not have the ability to install standard sheet metal screws, there are a couple things you can do. You can drill holes in the sheet metal for the bolts to go through. You would then use a lock washer and nut on the other side to secure…

view full answer...

Answer 3

Our best option for LED lights to replace your Peterson 130 style lights is the Rectangular LED Trailer Clearance Light, #MCL76AB for amber and #MCL76RB for red. These lights measure 5-13/16 inches long, 2 inches wide, 1-3/16 inches deep, and mounts…

view full answer...

Answer 4

I will be happy to help you find the right LED replacement lights for your horse trailer. Based on the information you have provided the amber LED replacement is #MCL76AB. The red version is #MCL76RB. Another option is to use Peterson lights #M353A…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...