Replacement LED Lights for a 1998 Ranger Boat Trailer

Question

Question:

I have a 1998 ranger trail for my 461vs ranger boat. I was looking to replace the trailer lights to LED. Do you have ones that will fit my trailer?

asked by: JP

0

Expert Reply:

We have a large selection of LED trailer lights which I have attached for you. You will need to go through these and pick the one that best matches your existing lights. You could also provide me with a dimensional photo to which I could then search our selection and find the best match for you but these would be your only options as we do not have information about what lights your trailer came with.

expert reply by: Conner L

0

Answer 1

I may have an option, but unfortunately we do not have any LED tail lights that are exactly 6-1/2" x 2-1/2". Instead we have the Optronics Miro-Flex LED Trailer Tail Light - Stop,Turn, Tail - Submersible - 12 Diodes - Red Lens #STL22RBH…

view full answer...

Answer 2

I spoke with my contact at Optronics and was informed that the Lumen Difference between the #STL22RB and the #STL72RB LED tail lights is not tested by Optronics. I was told though that the more LED lights that are in the tail light the brighter the…

view full answer...

Answer 3

A great choice for your boat trailer is the LED Trailer Light Kit for Trailers Over 80" Wide #TL16RK. This kit includes 2 tail lights which serve 8 functions (Stop, turn, tail, side marker, rear clearance, side reflector, rear reflector, and…

view full answer...

Answer 4

You can absolutely wire your trailer for both turn signals and brake lights using only one light per side, as long as each light has either 3 wires (tail lights, stop/turn, ground) or 2 wires with a ground that goes through the mounting hardware.…

view full answer...

Answer 5

The Optronics light part #STL72RB is made to fit a standard trailer light dimension so it makes sense that it would fit and work for your setup. I attached a picture that has the light dimensions for you to check to see if they match.

view full answer...

Answer 6

The first thing that I would recommend checking are the ground connections for the trailer side connector and the lights. Poor ground connections are the most common culprit of trailer wiring issues. The lights will have either a ground wire or they…

view full answer...

Answer 7

I spoke with my contact at Optronics and was informed that the Lumen difference between part #STL70RB and part #STL22RB LED stop, turn and tail lights is not tested by Optronics. I was told that the more LED lights in the tail light the brighter the…

view full answer...

Answer 8

Based on the picture you submitted it looks like you are looking for the part #STL22RB which is an LED version of the light you have that has 12 light emitting diodes.

view full answer...

Answer 9

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...