A-Frame Coupler For 2015 H&H Enclosed Trailer

Question

Question:

Hello, Im looking the frame coupler for an 2015 H&H enclosed trailer CA series. Vin# 533SC1212FC241266. Thank you,

asked by: Julio C

0

Expert Reply:

When looking up the specs for the H&H CA Series Flat Top Single Axle Cargo it said that this trailer uses a 2” A-frame coupler. The A-Frame Coupler Item # CA5100B will work with your trailer. It has a 2-1/4" hole diameter for jack: It requires (3) 3/8"-16 bolts for installation (not included). It will need to be welded on. If you need a bolt on coupler # DM14793-81 will work also.

I have attached all of our 2" A-Frame Couplers to this page.

expert reply by: Timothy G

0

Answer 1

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for attaching the…

view full answer...

Answer 2

It sounds like you're looking for a replacement a-frame coupler like #CA-5280-RB but in a silver-painted or zinc-plated finish. Please click on the link provided to see all bolt-on standard a-frame couplers for 2-5/16-inch balls. For the…

view full answer...

Answer 3

I attached a picture of the mounting holes for the Bulldog Heavy-Duty A-Frame Coupler, #BD44150WH301 that you referenced for you to check out so that you can compare them to the ones on your current coupler. Based on the picture you submitted this…

view full answer...

Answer 4

I do have a way for you to use your Avail tow bar with a 3-inch hitch receiver, however, there are no replacement shanks that fit a 3-inch hitch receiver. All you need to use a tow bar that fits a 2-inch hitch receiver in a 3-inch hitch receiver is…

view full answer...

Answer 5

The Bulldog Heavy-Duty A-Frame Coupler, #BD44150WH301, does not come with the attachment bolts. I have attached two images showing the bolt pattern measurements and the bolt hole sizes. I would recommend using grade 8 bolts, but grade 5 is acceptable…

view full answer...

Answer 6

The Demco A-Frame Trailer Coupler #DM14793-81 referenced in your question should work just fine as a replacement on your R-Pod Camper. As you mentioned, the coupler has a bolt-on installation and a weight capacity of 10,000 pounds. It is compatible…

view full answer...

Answer 7

I went to our warehouse and measured the Demco A-Frame Trailer Coupler #DM14793-81 to get you the dimensions you need. From the UNDERSIDE of the top plate, the part of the coupler that will actually contact the top of the A-frame, the hole centers…

view full answer...

Answer 8

Only solution will be to extend out the frame rails of your trailer so that you can install a standard coupler on to them. None of the options out there are going to be large enough to fit your frame channels that basically start too far apart. What…

view full answer...

Answer 9

I went out to the warehouse to measure the Demco A-Frame Trailer Coupler #DM14793-81 that you asked about and found that it measures 3-1/2" from the bottom to the top. I have attached a picture to demonstrate. If your safety chains are welded to…

view full answer...

Answer 10

Starting with the safety chains they really need to be attached to the trailer frame and not the coupler hardware. If there is no where to attach the chains on the trailer you can weld on safety chain mounting brackets such as #MB12, #MB38, or #MB58.…

view full answer...

Answer 11

Yes, you can replace your weld-on coupler with a bolt-on. You'll just need to drill the holes. Then, if you wanted to go back to a weld-on later that would be fine too. Just to confirm you can check with the trailer's manufacturer that…

view full answer...

Answer 12

Bulldog Heavy-Duty Cast Head A-Frame 2-5/16-Inch Coupler #BD44150WH301 is intended for standard 50-degree a-frame trailer frames. This unit is a bolt-on item and its rated 15,000-lb capacity is based on it being installed using all mounting holes to…

view full answer...