Lippert Components Power Stabilizer Trailer Jack # 298707 Retracted Height

Question

Question:

Part# LC298707 What is the total height when the Jack is retracted. Are the Control switch included?

asked by: Vakar

0

Expert Reply:

The Lippert Components Power Stabilizer Trailer Jack # LC298707 does include the control switch but not the Linc Remote # LC292614 which is compatible if you have the remote receiver # LC305117. I reached out to my contact at Lippert and the retracted height is 4 inches and the extended height is 30 inches.

expert reply by: Jason S

0

click to enlarge

Answer 1

Yes, the Replacement Lithium Converter #PD4590LICSV will work for your PD4590K18L. I checked with Power Dynamics to make sure that the difference between your part and the #PD4590K18LS8 would still allow for use with the Lithium Converter, and they…

view full answer...

Answer 2

I took a look at your now discontinued 2 Function Hydraulic Wireless Transmitter Remote P/N 248046, however Lippert does not disclose what battery type this remote takes, however I have another soluton. Since your remote is discontinued, along with…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Yes. You can replace the Progressive Dynamics PD4590K18NS2 with the Replacement Converter Section for Progressive Dynamics 4500 Series RV Power Control Center - 90 Amp #PD4590CSV without any issues. Both are 90 amp converters from the same Series and…

view full answer...

Answer 11

I spoke to Progressive Dynamics, the Progressive Dynamics REL 90A 4500 Series Inteli-Power Converter Section part #PD4590CSV is a fit for you 4590 panel. You have an older style panel which uses a different fan layout but the above will fit and is…

view full answer...

Answer 12

The Progressive Dynamics Converter #PD4655V is specifically designed to replace the WFCO 8955 you have on your 2014 Thor Hurricane 27K motorhome. This is compatible with your two 6volt batteries as they are going to be wired in series to create 12V…

view full answer...