Replacement Locking Knob and Lock Core for Thule Apex Bike Rack

Question

Question:

I have a Thule Apex 4 and need to replace the locking knob, cylinder, and key. Not sure which part number I need. thanks

asked by: Matt K

0

Expert Reply:

The knob you need for your Thule Apex is the part # 753-0073. Then the correct kit for the lock cores, keys, and change key is the part # TH450200.

expert reply by: Jameson C

0

Answer 1

Typically the lock will need to be in the unlocked position in order to unscrew the Locking Anti-Rattle Knob for Thule Apex Bike Racks and Rain Gutter Foot Packs - Qty 1 #753-0073 from the locking hitch pin. If your lock was in the locked position…

view full answer...

Answer 2

The Replacement Locking Anti-Rattle Knob #753-0073 will simply screw on to the anti-rattle hitch pin at the base of the rack. If you have a Thule Lock core you'll need to make sure it is in the unlocked position in order to install the knob-this…

view full answer...

Answer 3

If you unlock and remove the old lock core then the knob should then just spin off and you can repeat the same steps to install the new knob, Replacement Locking Knob for Thule Bike Racks part #TH79JV. Please note, you will need the change key to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...