Best Trailer Wiring Harness for a 2013 Chrysler Town and Country

Question

Question:

In May 2014 I purchased a receiver and CURT t-connector for my 2013 Chrysler Town and Country. I believe either you or CURT replaced the T-connector in 2016 because it failed. Today the fuse for the left rear taillight was blown and also a replacement fuse. I removed the CURT T-Con and that corrected the problem fuse didnt blow. Is this a known problem with the CURT product no. 56150? Should I try another one or just try a different manufacturer? Should I contact CURT directly? Thanks in advance.

asked by: Charlie

0

Expert Reply:

I cannot speak specifically to the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # C56331 however, in our experience we have indeed had customers who experienced excessive problems with their Curt wiring harnesses whether that be a short in the wiring or failed converter box. What we have found is that the best manufacturer for wiring harnesses in regard to quality and longevity is Tekonsha. If you would like the Correct Tekonsha harness for your vehicle, then I highly recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56331.

If you need a refresher on how to install the harness, then you can take a look at the attached install video.

expert reply by: Conner L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Best Trailer Wiring Harness for a 2013 Chrysler Town and Country

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching