Replacement 14 x 14 Inch Vent Lid with Continuous Hinge

Question

Question:

the vent is 14 x 14 with continuous hinge. it is NOT original to the camper. What do I need to look at to be sure Im getting the right lid?

asked by: Claude

0

Expert Reply:

You will want to look at the size and the hinge style when looking for a replacement vent lid. There are different styles of a continuous hinge. If you can snap a pic of the existing hinge on the vent or lid and email that to me I can point out the lids that match.

Basically there is the style seen on lid # BVD0449-A03 which is all plastic and has 3 openings in it.

expert reply by: Michael H

0

Answer 1

The key to picking out a replacement lid for a standard 14 x 14-inch trailer roof vent is matching the hinge type. Trailer makers typically don't keep track of smaller items like vents that are used in fabrication of their trailers so you can…

view full answer...

Answer 2

To determine which replacement lid you need you will need to check the hinge on the roof of your vent lid. I have included an chart that has the most common lids and shows the hinges. Once you identify the hinge you will need one of the following…

view full answer...

Answer 3

The Hengs lids we offer do not have continuous metal hinges but we do have a few that do have that hinge style like the #CAM40161 which is a white polycarbonate lid.

view full answer...

Answer 4

We carry replacement lids for Elixir RV Roof Vents that have the appropriate hinge, which is what I believe you are asking about; the hinge on these lids are not available as a separate entity, however. The replacement lid for your roof vent will be…

view full answer...

Answer 5

To determine which replacement lid you need you will need to check the hinge on the roof of your vent lid. I have included an chart that has the most common lids and shows the hinges. Once you identify the hinge you will need one of the following…

view full answer...

Answer 6

It sounds like you are looking for a replacement vent cover for your camper. Manufacturers used several different companies for the vents on their trailers so it is difficult to know exactly what you have. To find the correct replacement lid you will…

view full answer...

Answer 7

To remove the damaged vent cover, remove the connection to the actuating strut, so the cover can tilt all the way upwards. To do this, you will need to remove the interior screen, the knob and the interior trim piece. Then, remove the two screws that…

view full answer...

Answer 8

The hinge looks VERY similar to the part #BVD0449-A03 that we offer but slightly different possibly as it's hard to see in the picture. Does the #BVD0449-A03 look like what your roof vent had prior?

view full answer...

Answer 9

Thanks for the picture of your RV roof vent lid that you need a replacement for. Seeing that makes it easy to know what you'd need with the part #BVD0449-A03.

view full answer...

Answer 10

I was able to confirm with the manufacturer that the Replacement Actuator for Thomas Payne Seismic Power Recliner part #SC96MR cross-references to the QDPT-01-002. Therefore, the two are cross-compatible.

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...