Replacement Lid for Ventadome RV Roof Vent

Question

Question:

Everything I’m seeing says this should be the replacement vent dome for our LTV Unity 2014MB but the piece that slides the vent up and down doesn’t look the same as ours. I’m including a picture to show you what i mean, if you can help me out that would be awesome! Thanks in advance for your help!

asked by: Lisa O

1

Helpful Expert Reply:

Thanks for the picture of your RV roof vent lid that you need a replacement for. Seeing that makes it easy to know what you'd need with the part # BVD0449-A03.

expert reply by: Jameson C

1

Ventadome Lid
(click to enlarge)

Answer 1

Thank you for the photo of the information on your vent cover! Based on these numbers I was able to determine that the Ventline Replacement Dome Assembly #BVD0449-A01 that you referenced will work well for you. This is a white, wedge shape cover. If…

view full answer...

Answer 2

If your existing roof vent has this stamped on it AS-13 M-VDO449 and has a the same connection style as the Ventline Replacement Dome Assembly #BVD0449-A01 product that you mentioned then this vent will fit your trailer. I was able to pull one that…

view full answer...

Answer 3

The dimensions of a Group 27 battery are 12 inches long by 6-5/8 inches wide by 9-3/16 inches tall so for a box that can carry two of them we have the TorkLift PowerArmor Locking Battery Box #TLA7708R which has dimensions of 26-3/4" long x…

view full answer...

Answer 4

To remove the damaged vent cover, remove the connection to the actuating strut, so the cover can tilt all the way upwards. To do this, you will need to remove the interior screen, the knob and the interior trim piece. Then, remove the two screws that…

view full answer...

Answer 5

You will want to look at the size and the hinge style when looking for a replacement vent lid. There are different styles of a continuous hinge. If you can snap a pic of the existing hinge on the vent or lid and email that to me I can point out the…

view full answer...

Answer 6

The hinge looks VERY similar to the part #BVD0449-A03 that we offer but slightly different possibly as it's hard to see in the picture. Does the #BVD0449-A03 look like what your roof vent had prior?

view full answer...

Answer 7

I was able to confirm with the manufacturer that the Replacement Actuator for Thomas Payne Seismic Power Recliner part #SC96MR cross-references to the QDPT-01-002. Therefore, the two are cross-compatible.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Replacement Lid for Ventadome RV Roof Vent

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching