What are the Diameters of Bearing Buddy Bras # BB19B, # BB23B, and # BB17B

Question

Question:

Howmdo I determine which model buddy bras I need. I have a 1970s model trailer with straight 1 inch axlel bearings. What are the measurements of the different models?

asked by: G L

0

Expert Reply:

We have three bearing buddy bras, the Replacement Bearing Buddy Bras # BB17B that you referenced has a diameter of 2 inches.

The Replacement Bearing Buddy Bras # BB19B has a diameter of 2-1/8 inches, and the Replacement Bearing Buddy Bras # BB23B has a diameter of 2.441 inches.

The best way to determine which one you need, is to take the model bearing buddy that you have and check all of the product descriptions to see if your model is listed as one of the bearing buddies that the bra is compatible with, or measure the outside diameter of your bearing buddy and buy the correlating bra for the bearing buddy.

expert reply by: Jameson C

0

Answer 1

The plastic caps for the Bearing Buddy bearing protectors that you are looking for are the Bearing Buddy Bras. We carry three different bras, #BB17B, #BB19B and #BB23B that fit different ranges of Bearing Buddy sizes. You should choose the Bearing…

view full answer...

Answer 2

The portion you need to measure is not the cap, but the the hub bore. Remove the grease caps and measure the diameter of the opening the caps occupy. This is the hub bore. You will need an accurate measuring devices like a set of dial calipers that…

view full answer...

Answer 3

To determine which Bearing Buddy would fit your trailer you will need either a measurement of the hub on your trailer, or the bearing part numbers. To measure your existing hub it is recommended to use digital calipers to get a precise measurement.…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

What are the Diameters of Bearing Buddy Bras # BB19B, # BB23B, and # BB17B

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching