Landing Gear Recommendation for 2006 Keystone Montana Mountaineer

Question

Question:

Will these fit on a 2006 Montana Mountanier ?

asked by: Melvin B

0

Expert Reply:

Lippert made specific replacement landing gear for your 2006 Keystone Montana 5th Wheel.

Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear # LC178653 and Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear # LC178652. No other kit we offer would fit.

expert reply by: Jameson C

0

click to enlarge

Answer 1

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 2

Sounds like the correct follower leg you would need is the #LG-179014 that you referenced. The overall length of the leg is 33-1/2 inches and the distance from the inside of the two brackets is 17-1/2 inches. Check out the picture I attached for more…

view full answer...

Answer 3

I do not recommend adding grease zerk fittings to a jack leg that did not originally come with them. drilling holes into the jack could compromise its structural integrity. You would need to open up the jack legs to add grease. Before adding any…

view full answer...

Answer 4

The correct replacement follow leg you are looking for is the part #LG-179014. This matches the part numbers and dimensions you mentioned as well.

view full answer...

Answer 5

Lippert made specific replacement landing gear for your 2006 Keystone Montana 5th Wheel. Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear #LC178653 and Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear #LC178652.

view full answer...

Answer 6

If you have a Venture landing gear set on your 2006 Keystone Cougar the Stromberg Carlson repair kit part #LG-146059 would be the correct kit for you. As you take the jack apart you should be able to see how it all comes apart and reinstalls with the…

view full answer...

Answer 7

In order to find the correct replacement landing gear leg for your Open Range 430RLS 5th wheel trailer I would need to know the brand and part number of the landing gear leg you currently have on your trailer. These should be stamped or etched into…

view full answer...

Answer 8

I went to the warehouse and took some measurements of the Replacement Lead Leg, part #LG-177202 for you. I have attached a photo of the leg with the measurements noted. From the top of the leg to the top of the upper bracket is 7 inches. To the top…

view full answer...

Answer 9

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just keep…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Landing Gear Recommendation for 2006 Keystone Montana Mountaineer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching