Hardware Kit Recommendation for Curt Hitch C13131

Question

Question:

looking for a hardware kit for a curt hitch 13131. thank you

asked by: George Z

0

Expert Reply:

We used to carry the Curt hitch C13131 that you referenced so we can get you the replacement hardware kit for it with part # RHK. What you'll need to do is select Curt from the drop down menu of the product page and then enter the part number of the hitch and you'll be set.

expert reply by: Jameson C

0

Answer 1

For your 2019 Ford Escape Titanium that came without the tow package the correct trailer wiring harness is the part #118802. This is a custom fit kit that installs by plugging inline with the taillight connectors of your vehicle. The converter box…

view full answer...

Answer 2

On a new vehicle it's going to be much easier to run the power wire for trailer wiring like the part #C56320 outside of the vehicle as opposed to pulling up the carpet and then trying to get it through the firewall. I attached a help article…

view full answer...

Answer 3

When installing the wiring harness #C56320 in your 2017 Ford Escape the power wire should be ran directly to the battery. It's protected by the included fuse. There's no need to install a switch because your Escape's tail…

view full answer...

Answer 4

I don't recommend connecting the power wire of the #C56320 to anywhere but the vehicle battery. Using the 12 volt outlet in the cargo area of your 2018 Ford Escape may not work properly. The converter needs to receive power from an isolated 12…

view full answer...

Answer 5

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56383 does refer to that sheet. I've attached the link but also a photo of the sheet to ensure you get what you need in a format that works for you.

view full answer...

Answer 6

The Tow Ready 2 Inch Hitch Ball, part #63845, you have referenced needs to be torqued to 250 foot pounds. It is recommended to frequently check that the ball is tightened to these specifications. If you are meaning the mounting bolts that are used to…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Hardware Kit Recommendation for Curt Hitch C13131

Product Page this Question was Asked From

Continue Researching