Replacement Tarp for TruXedo Tonneau Cover on 2006 Toyota Tundra

Question

Question:

It is a SR5 Double cab

asked by: Doug

0

Expert Reply:

I could not find a reference to that part number though we may be able to narrow it down some. Do you have a 6' or 8' bed? Do you have bed caps? And finally, access cab or double cab?

expert reply by: Kyle S

0

Doug

3/16/2018

It is a SR5 Double cab

Reply

Kyle S.

3/16/2018

There are a number of possibilities based on the tonneau cover you have on your 2006 Toyota Tundra so you do need to know either the model number of the name of the cover to get the right replacement. The replacement tarp for the TruXedo Edge TX845101 is Replacement Cover # TX8451-CVR. The replacement tarp for the TruXedo Lo Pro QT # TX545101 is Replacement Cover # TX545101-COVER. The replacement tarp for the TruXedo TruXport # TX245101 is Replacement Cover # TX2451-CVR.

Reply

Answer 1

Thanks for the information. I checked with TruXedo and to replace just the cover on your 2012 Ford F-150's 5-1/2' bed you will need the Replacement Cover for TruXedo Lo Pro Soft, Roll-up Tonneau Cover item #TX5671-CVR. You will want…

view full answer...

Answer 2

There was a pretty big change for the Chevy Silverados between the years 2018 and and 2019 which means the tonneau cover companies had to come up with new fits for the trucks. So what that means for you is that a tonneau from a 2017 Silverado would…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

There is actually a carrier specifically for your application. Well, not vaulting poles, but 6 inch PVC pipe. Take a look at Conduit Carrier Kit #RP7054900. It fits 6 inch diameter PVC schedule 40 or 80 and this set up can be locked using a padlock…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 11

Both of the Curt hitch receivers have the same bolt hole measurements. It's 9 inches from the first hole (Closest to the front of the truck) to the second hole and 5-1/2 inches from the second to the third. There's 39 inches across…

view full answer...