Clearance Of The Curt Trailer Hitch Receiver To The Ground For 2006 Lexus GS 300

Question

Question:

Hi there, Is there a measurement of how high the hitchs lowest part is from the ground? There were some reviews that say the hitch scrapes easily.

asked by: Feli

0

Expert Reply:

On the Curt Trailer Hitch Receiver # C11372. The hitch pinhole to the edge of the bumper will be about six inches. From the top receiver opening down to the ground will be around 10 inches.

expert reply by: Timothy G

0

Answer 1

There is no drilling involved in the installation of hitch part #11372 from Curt. Lexus provides weld-nuts on the frame rails for hitch attachment. However, you will need to trim a piece of heat shielding with a set of tin snips. I have added a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 5

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

To add a hitch to your 2024 Honda Pilot, I recommend the etrailer item #e27KR. This hitch is custom fit and bolts to your Honda with included hardware. I really like the etrailer hitch item #e27KR because it installs behind your rear bumper cover and…

view full answer...

Answer 12

To add a hitch to your 2024 Jeep Grand Cherokee L, I recommend the Draw-Tite item #DT42GR. This hitch is custom fit and bolts to your Jeep with included hardware. This is a class III hitch with a 2" receiver. It has a 7,500 lbs towing capacity…

view full answer...