Does Curt Hitch 11372 Require Drilling to Install on a 2007-2010 Lexus GS350

Question

Question:

Is this a bolt on product, or is there drilling involved?

asked by: Harry P

0

Expert Reply:

There is no drilling involved in the installation of hitch part # 11372 from Curt. Lexus provides weld-nuts on the frame rails for hitch attachment.

However, you will need to trim a piece of heat shielding with a set of tin snips. I have added a link to the instructions below that picture where the heat shield must be trimmed.

expert reply by: Patrick B

0

Answer 1

I do have some information that will help us determine the ground clearance you can expect with the Curt Class I Trailer Hitch, #C11372, on your 2008 Lexus IS 350, however, we have not had the chance to install this hitch on that vehicle yet, so we…

view full answer...

Answer 2

We only have one trailer hitch confirmed to fit your 2008 Lexus GS 350 but it is a custom fit so no drilling is required for installation. I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" #C11372. For your bike…

view full answer...

Answer 3

The only hitch we offer for your 2011 Lexus IS 250 Sedan is the Curt Hitch part #C11372 which is a Class I hitch with a 1-1/4 inch opening. There is no good way to use a 2 inch bike rack in a 1-1/4 inch hitch. You would have to use an adapter like…

view full answer...

Answer 4

There isn't a specific distance you want to have between the bumper of a vehicle and the hitch ball, but in general you'll want more than an inch. This will give you additional leeway when hitching up the trailer so that you don't slam…

view full answer...

Answer 5

On the Curt Trailer Hitch Receiver #C11372. The hitch pinhole to the edge of the bumper will be about six inches. From the top receiver opening down to the ground will be around 10 inches.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...